1、瓦的正確鋪放方式

1. The correct laying method of tiles

對于這類產品的鋪放方式有兩種，主要是看產品的長度，若是長度小于等于15M的屋面，建議采用重疊式，若是長度大于等于15M的屋面，則建議采用交錯式。

There are two laying methods for this type of product, mainly based on the length of the product. If the length of the roof is less than or equal to 15M, it is recommended to use overlapping type. If the length of the roof is greater than or equal to 15M, it is recommended to use staggered type.

2、專用釘正確使用方法

2. Correct usage of specialized nails

對于專用釘?shù)倪\用，一定要依照正確的方式進行，將其打在瓦骨部位才能起到防水效用。同時固定間隔橫豎控制在50CM～100CM，另外專用釘須由瓦的下端往屋頂方向打才能有美觀、密封、整齊的效果。

For the use of specialized nails, it is necessary to follow the correct method and hit them in the center of the tile bone to achieve waterproof effect. At the same time, the fixed spacing should be controlled between 50CM and 100CM horizontally and vertically. In addition, special nails must be driven from the lower end of the tile towards the roof to achieve a beautiful, sealed, and neat effect.

3、安裝密封條脊瓦封檐蓋

3. Install sealing strip ridge tile eaves cover

將密封條截成兩半，然后照著瓦型壓在屋面上，再用專用釘穩固，在瓦側面的交界處，要用水泥作密封處理后直接蓋上脊瓦，脊瓦底部用小瓦檔收尾，另外瓦的下端即屋檐處直接安裝封檐蓋使用螺釘固定。

Cut the sealing strip in half, then press it onto the roof according to the tile shape, and use special nails to stabilize it. At the junction of the tile sides, seal with cement and directly cover the ridge tile. The bottom of the ridge tile is closed with a small tile stop. In addition, the lower end of the tile, i.e. the eaves, is directly installed with a eaves cover and fixed with screws.

4、突出部分防水處理

4. Waterproofing treatment for protruding parts

對于防水方面的處理，可以采用V字型質料，當然它有不同的材料和規格。在確認時，需依照實際情況而定，做接水處安裝在底部后在上面鋪放彩鋼瓦。

For waterproofing treatment, V-shaped materials can be used, although they come in different materials and specifications. When confirming, it is necessary to determine according to the actual situation, install the water connection point at the bottom, and then lay colored steel tiles on top.

5、傾斜面連接安裝

5. Installation of inclined surface connection

待上面四道工序都做好后，要進行傾斜面的連接安裝。其實就是兩屋面瓦按照角度和長度切斷后，底部安裝接水處理的施工，在瓦下安裝接水材料，然后用防水粘合劑或水泥做收尾處理。

After all four processes are completed, the final step is to connect and install the inclined surface. In fact, it is the construction of installing water treatment at the bottom after cutting the two roof tiles according to the angle and length. First, install water treatment materials under the tiles, and then use waterproof adhesive or cement for finishing treatment.

本文由濟南彩鋼瓦廠友情奉獻.更多有關的知識請點擊:http://elpomelo.com真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from Jinan Color Steel Tile Factory. For more information, please click: http://elpomelo.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned